{"id":259,"date":"2026-11-17T10:07:45","date_gmt":"2026-11-17T09:07:45","guid":{"rendered":"https:\/\/www.cormidi.com\/dal-cantiere\/cmf1200-in-pendenza-cosa-dicono-i-dati-di-stabilita\/"},"modified":"2026-11-17T10:07:45","modified_gmt":"2026-11-17T09:07:45","slug":"cmf1200-in-pendenza-cosa-dicono-i-dati-di-stabilita","status":"publish","type":"cor_cantiere","link":"https:\/\/www.cormidi.com\/en\/dal-cantiere\/cmf1200-in-pendenza-cosa-dicono-i-dati-di-stabilita\/","title":{"rendered":"CMF1200 on slopes: what the stability data says"},"content":{"rendered":"<div data-no-translation>\n<p>Anyone who works on sloped terrain knows the problem isn&#8217;t just climbing. It&#8217;s maintaining control when the bucket is full, when traversing an embankment sideways, when the ground is uneven and every extra meter of elevation gain increases the risk of tipping over. Before taking a machine onto an inclined face, you need to know exactly what it can handle and what it can&#8217;t.<\/p>\n<h2>The four angles to know<\/h2>\n<p>The CMF1200 is rated with four distinct maximum working slope values, which vary depending on two variables: the direction of travel (frontal or lateral) and load conditions (empty or full load). It is not a single generic figure: it is a precise matrix that helps plan work in the field.<\/p>\n<h2>Empty: the highest values<\/h2>\n<p>When the bucket is empty, the CMF1200 declares a maximum frontal slope of <strong>102% (46\u00b0)<\/strong>. Laterally, still empty, the value drops to <strong>58% (30\u00b0)<\/strong>. These numbers describe the limit conditions in the absence of a load: useful to know for positioning phases, for reaching the work point, or for returning at the end of the cycle.<\/p>\n<h2>At full load: the situation that matters most<\/h2>\n<p>It is when material is being transported that the slope becomes a critical variable. With a load, the declared maximum frontal slope is <strong>44% (24\u00b0)<\/strong>. The lateral loaded figure, on the other hand, rises to <strong>77% (38\u00b0)<\/strong>, a value higher than the frontal loaded one. Those who plan site routes must take this difference into account: in certain situations, tackling the slope sideways with a load may fall within spec, while a steep frontal section could exceed the declared limit.<\/p>\n<ul>\n<li>Frontal slope empty: <strong>102% \u2013 46\u00b0<\/strong><\/li>\n<li>Frontal slope at full load: <strong>44% \u2013 24\u00b0<\/strong><\/li>\n<li>Lateral slope at full load: <strong>77% \u2013 38\u00b0<\/strong><\/li>\n<\/ul>\n<h2>Tracks and weight distribution<\/h2>\n<p>On sloped terrain, tracks distribute weight over a continuous contact surface. This behavior differs from that of wheeled machines, which on mud, wet grass, or uneven sloped ground tend to lose traction and concentrate forces on reduced points. For the CMF1200, which often operates on green landscaping sites, earthmoving in hilly areas, or drainage work on embankments, tracked traction is an integral part of the operating conditions for which the slope values have been defined.<\/p>\n<p>Knowing the four slope values of the CMF1200 before starting a job is not a formality: it is the way to organize routes, decide where to load and where to unload, and establish which sections are traveled empty and which at full load. Bring the CMF1200 to your site and see for yourself how it responds to your faces.<\/p>\n<\/div>","protected":false},"excerpt":{"rendered":"<p>Steep faces, traverses on embankments, work with a full load: the slope values of the CMF1200 explain where this machine can operate and how.<\/p>","protected":false},"featured_media":260,"template":"","meta":{"_acf_changed":false,"footnotes":""},"class_list":["post-259","cor_cantiere","type-cor_cantiere","status-publish","has-post-thumbnail","hentry"],"acf":[],"_links":{"self":[{"href":"https:\/\/www.cormidi.com\/en\/wp-json\/wp\/v2\/cor_cantiere\/259","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.cormidi.com\/en\/wp-json\/wp\/v2\/cor_cantiere"}],"about":[{"href":"https:\/\/www.cormidi.com\/en\/wp-json\/wp\/v2\/types\/cor_cantiere"}],"version-history":[{"count":0,"href":"https:\/\/www.cormidi.com\/en\/wp-json\/wp\/v2\/cor_cantiere\/259\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.cormidi.com\/en\/wp-json\/wp\/v2\/media\/260"}],"wp:attachment":[{"href":"https:\/\/www.cormidi.com\/en\/wp-json\/wp\/v2\/media?parent=259"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}